banner  

Go Back   FTA Files Forums for all FTA Satellite Receivers > General Discussions > FTA General Discussion


FTA General Discussion FTA Satellite and FTA Receiver issues.

Reply
 
Thread Tools Rate Thread
  #1 (permalink)  
Old 12-14-2011, 11:56 AM
VIP
 
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 2
raul1980 is on a distinguished road
Talking how to set up a captive w 800s

hi iam new to fta and i got a captive w 800s and i need some help to setup htis reciber and i hace no idea how thank you
Reply With Quote
  #2 (permalink)  
Old 12-14-2011, 01:29 PM
sam sam is offline
Senior Member
 
Posts: 1,240
Thanks: 11
Thanked 126 Times in 67 Posts
Rep Power: 138
sam has a reputation beyond reputesam has a reputation beyond reputesam has a reputation beyond reputesam has a reputation beyond reputesam has a reputation beyond reputesam has a reputation beyond reputesam has a reputation beyond reputesam has a reputation beyond reputesam has a reputation beyond reputesam has a reputation beyond reputesam has a reputation beyond repute
Default

dig....this .........c/p.....

Captive works Private and Public Setup With Dongle ......


This guide is for the Captive works 700 & 800. it will work with the UH-100 dongle or the 2011 dongle.


Load the latest file into the receiver and follow the prompts; reboot as asked.
CW 800 file
CW 700 file
Plug the USB dongle into the USB port of the receiver. Then connect the dongle to your router with an Ethernet cord. Reboot by turning the switch at the back off for a second and then on again. While the machine is booting you should notice a USB Ready message.

Enter the menu, then enter System Settings. First select OSD and turn Auto Roll off at the bottom of the page. Then exit OSD and enter System. In this menu Change Channel NO. to SID and turn Auto TP on.

Then set your antenna settings according to your setup and scan satellites

Re-enter Main menu, select Accessories then select Network Setting. (Network setting replaced the setup wizard when the dongle is unplugged
In Network settings select IP info, Here Your IP address fields should be populated and you should see Net Status: Connect. Server Status Should read Disconnect [0] at this point.

Exit IP info and enter Server Setting. In this menu use your left and right directional buttons to select different server slots and the up and down to adjust each server slot.

For Public. Select 1(Public) and input your code into the User Name row. Press the green button to enable. If everything is input correctly you should see Connect CAID[1816] (this is the southern provider) Press the right directional arrow and you should see 2(public). Input the same code into the user name row. Then press the green button to enable. If everything is input correctly you should see Connect CAID[1815] (this is the Northern provider).

There are 4 public slots and 36 private slots. You cannot input private server information in the reserved public slots. The server information is embedded in the file and cannot be changed.

The blue button toggles between public and private, you canít run both with the current files.

After you see Connect CAID every where you want to re-enter IP info. Now you should see Server Status Connect and the number of servers your connected to will be seen in [square brackets]

Exit the menu and tune into a known working channel

Press F1 + 0000 = patch enable/disable toggle Patch must be enabled
Press F1 + 5555 = Card Sharing ECM Enable/disable toggle Card sharing must be enabled

Wait for about 20 minutes or less and enjoy TV.........
__________________
REP +/-
THANKS.
Reply With Quote
Reply

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:


Similar Threads
Thread Thread Starter Forum Replies Last Post
Set-up files captive works 800S, new trial subscription Mdesai123 General Paid IKS Servers Discussions 1 08-29-2012 04:02 PM
Cw-800s TED97 CaptiveWorks 800 Instructions 4 12-22-2011 06:42 PM
CW-800S with USB Dongle set up juano CaptiveWorks Discussion 10 05-30-2011 05:01 PM
CW 800s goodbeer CaptiveWorks Discussion 2 03-20-2011 11:36 AM
Help me need sept 4th bins for captive works 800s NEESHARM CaptiveWorks Discussion 2 09-04-2009 07:43 PM


All times are GMT -7. The time now is 01:22 PM.