banner  

Go Back   FTA Files Forums for all FTA Satellite Receivers > FTA Files & FTA Instruction & FTA Discussion Section > i-Link FTA Receivers Support > i-Link Files & Instructions > i-Link IR-210/IR-220 FTA Files > i-Link IR-210/IR-220 Instructions


Closed Thread
 
Thread Tools Rate Thread
  #1 (permalink)  
Old 10-04-2011, 02:54 PM
Ekim's Avatar
Jr Super Moderator
 
Location: Afghanistan
Posts: 15,270
Thanks: 1,031
Thanked 2,711 Times in 1,776 Posts
Rep Power: 870
Ekim has a reputation beyond reputeEkim has a reputation beyond reputeEkim has a reputation beyond reputeEkim has a reputation beyond reputeEkim has a reputation beyond reputeEkim has a reputation beyond reputeEkim has a reputation beyond reputeEkim has a reputation beyond reputeEkim has a reputation beyond reputeEkim has a reputation beyond reputeEkim has a reputation beyond repute
Default How To Set Up IR210 or IR220 On A Private Newcamd Card Share

How to setup your IR210, IR220, or IS8000 on a private NewcamD card share.

I think it's time to open the doors and broaden our horizons. The fact that your Ilink model that I listed above has the ability to connect to a private server is an option for you that may one day be put to use.

For those interested here's basic instructions so that you will not find the task of doing so too difficult.

First load the newest firmware file to the receiver that is supported above.
Since I'm using a IR-210 the latest file is the 2.84

then do a factory reset (this is very important, the first time I tried doing this it didn't work and it was due to this step so do it!)

then go into your network tab then net applications
the default setting is EPCS which is ilink's public server Public no longer works
Change the EPCS to Dream
once you do that you should set the settings like the picture that I will post
Mind you this is for use with the private server so if you use another you will use a different domain name and server port #

In the "Authorization" area you will input your user ID and password which on the private server is the same

also input the des key which is also input into the des area

now if you exit your settings will stay how you put them so at this time exit and then re enter to make sure all your settings are correct

after so go back into network and into IP Setup for after doing the factory default the IP Setup area goes to "not used" so turn it back to "auto" or "manual" or whatever you used before

the last step is scanning your satellites

afterdoing so simply press exit and watch tv

notice on the bottom right you now have "connection: 1" referring to the number connection in dream private server area

NOTE: if you want to go back to the Ilink public iks simply change dream back to EPCS and it should revert automatically

__________________








I WILL NO LONGER ANSWER RECEIVER RELATED QUESTIONS BY PERSONAL MESSAGES


The Following 9 Users Say Thank You to Ekim For This Useful Post:
Closed Thread

Bookmarks

Thread Tools
Rate This Thread
Rate This Thread:


Similar Threads
Thread Thread Starter Forum Replies Last Post
Neosat iPro Newcamd for Akai japan Nov/11 free trial FTA PRO Neosat FTA Files 0 12-02-2011 01:35 PM
MULTIPLE SERVERS IN NEWCAMD rev12_24 FOR THE NEOSAT Ipro 2000 Ekim Neosat Instructions 0 07-10-2011 01:39 PM
nano2 conversion to i link private card share server sam Conaxsat Nano 2 Instructions 3 01-04-2011 04:39 PM
CaptiveWorks Card share Zero Gravity CaptiveWorks Discussion 19 10-16-2009 04:38 PM
Private Card Sharing - Be Careful Putski IKS Discussions 2 10-01-2009 06:09 PM


All times are GMT -7. The time now is 02:28 PM.