Please follow every step and you will have your Nfusio, working, you have to use the T54.bin all the other are death....
you need to go to IKSprivateserver.com and dowload the archives 1 and 2,one of them say nova , but do'n t worry it works for Solaris also
Instructions to convert the NFusion receiver to work on the NFPS System
This system can convert the NOVA, SOLARIS & PHOENIX
Please note this system does not work with the NFusion HD Receiver
CAUTION: All files have to be loaded using the Null Modem Cable.
Please do not load using the WEB LOADER as it will Kill the receiver.
This system does not work with these LNBs - Legacy Twin or Quad, and the
respective switches including the SW21.
The Only switches this system will work with are the 4x1 DiSEqC switch and
the 22 KHz switch.
1. Make a Folder called NFPS Files. Download “Archives 1 & 2” and Unzip them and
place them in this folder.
2. The files are ( NFusion Loader v. 1.1, boot_r3x_to_g3x_v1.33.bin, boot_g3x_to_r3x_v1.23.bin,
081121_borisT4.bin, R3X_2.0.1_newcam.bin, Cheditor_v16c.exe.)
3. Into this folder also download the latest Channel List Files.
4. Now check your dish setup and make a note of where 119 and 110 are connected on
the DiSEqC switch (Port 1, 2, 3 or 4) or the 22 KHz switch. This is to help you select
the correct Channel list that you need to load to the receiver.
5. Download T54.zip, unzip it and save it in the same folder.
6. Now the procedure to Load the files.
Open NFusion Loader v1.1, Click on MAIN and it will change to Boot>>.
Now check your computer and verify what COM Port is being used, and click on Com1 to
change to either 2,3 or 4.
Next click on OPEN FILE and select “boot_r3x_to_g3x_v1.33.bi n” and click on START
NFUSING, click OK and Switch ON the receiver using the rear rocker switch. It will start
loading the file. Wait till it says “Good” on the front panel. Reload the same file again as
This time when it finishes loading it will say “ne nu” on the panel. That’s fine.
Next, Click on Boot>> and it will change to MAIN.
Now click on OPEN FILE and select “081121_borisT4.bin” – this is the working BIN.
Click on START NFUSING and then click on OK, now switch the rear Rocker switch
OFF and ON and the Bin will begin loading. When complete the panel will show “hold”
and then “Good”.
Now click on and open “Cheditor_v16c.exe”. This program loads the channel list to the receiver.
Click on “Transmit” and then on “Serial Set” to select the correct COM Port (1, 2, 3 or 4) and
Next click again on “Transmit” and then on “Send Data”. Double click on the Channel List
needed according to the way your LNBs are connected to your Switch. On completion it will
show “hold”, then “Good” and then “0000”. Load the Channel List a second time and this time
it will show “hold”, then “Good” and then “0001”. Now you are done.
The Channel lists you will have in the folder for selection are as follows:
Select “digital119” if you have only one LNB pointed at 119.
Select “digital110” if you have only one LNB pointed at 110.
If you have Two LNBs pointed at 119 and 110 connected to a 4x1 DiSEqC switch, use the
110 on Port 1 and 119 on Port 2, Choose “adigital1-2”
119 on Port 1 and 110 on Port 2, Choose “adigital2-1”
110 on Port 1 and 119 on Port 3, Choose “adigital1-3”
119 on Port 1 and 110 on Port 3, Choose “adigital3-1”
110 on Port 1 and 119 on Port 4, Choose “adigital1-4”
119 on Port 1 and 110 on Port 4, Choose “adigital4-1”
110 on Port 2 and 119 on Port 3, Choose “adigital2-3”
119 on Port 2 and 110 on Port 3, Choose “adigital3-2”
110 on Port 2 and 119 on Port 4, Choose “adigital2-4”
119 on Port 2 and 110 on Port 4, Choose “adigital4-2”
110 on Port 3 and 119 on Port 4, Choose “adigital3-4”
119 on Port 3 and 110 on Port 4, Choose “adigital4-3”
If you have the Two LNBs pointed at 119 and 110 connected to a 22KHz switch,use the
If 110 is on 22KHz ON and 119 is on 22 KHz OFF, Choose “adigitalon-off”
If 119 is on 22KHz ON and 110 is on 22 KHz OFF, Choose “adigitaloff-on”
Now you will need to Load the T54.bin.
Open the 1.1 or 1.31 loader and Click on OPEN FILE and select the T54.bin. Make sure you are in MAIN mode
and Click on START NFUSING. Click on OK and reboot the receiver and the Bin will start loading. When
finished it will show HOLD and then GOOD and then 0001.
The software we are using were made for the European Market and the display format is in the PAL system.
The American/Canadian TV works in the NTSC system and as such we need to convert from PAL to MULTI.
When you connect the Receiver to the TV and Start the receiver, you will find a scrolling screen. Change the
Channel with your remote to either channel 3 or Channel 594 which are FREE channels in the Dish Network
system. These channels are not encoded and so have a picture. You will hear sound of people talking with the
picture scrolling vertically. Press the following Buttons on your Receiver Remote in the following order.
Press the Menu Button, press once the DOWN Channel button, Press OK, Press the DOWN Channel button
again, and finally press the Left or Right Volume button once.
You should now see a Blue screen with MULTI shown.
Press Up button and change all the Languages to English.
Press Exit. And you will see the Free Channel.
Now we need to enter other information like the code etc.
Press Menu>Internet>OK>NEWCAMD>press 9949 (you will not see any change)>press OK
It should take you to another Page, Click OK on Server Setting 1 and it will open another Page.
This is where you will enter all the other important information.
The first line “Server Address” – It should read – fenfu.dynsite.net. or fenfui.dynsite.net as given to you – EXIT
Next line is “User Name” – Here you have to input the Donation # assigned to you by NFPS. – EXIT to save
Next is Password – Here too you input the same Donation # – EXIT to save
Please note each number you enter make sure it is showing on the screen. Check and recheck before you save.
The next line is DNS Keys – These will be already entered.
However if you should need it then here it is: 6103403445406970987123412134
Next Line is Port1 – Here you will enter the Port assigned to you. Although the Port may be the correct one you
need to reenter the Port. – EXIT to Save.
Now you will have a Black screen.
You will need to do a Hard Reboot. Shut OFF and ON the receiver with the rear Rocker switch.
The screen will scroll. Check that you have Channel 594 or 3 showing on the receiver panel. Press SIZE button
to stop the scroll.
Again go back to NEWCAMD and change it from OFF to ON. Press Exit.
Again go back into SERVER SETTINGS and Exit out of it. Reboot. Press SIZE to stop the scroll.
Now press any channel number and you should be up and running. If not then go back into Server Settings,
Exit, Reboot Press SIZE to stop the scroll. Now again select the channel you want.
Watch and enjoy TV.
LATEST ADDITION OF CHANNEL LISTS
Channel list is now available for DP/DPP LNBs for 119 and 110 Satellites.
Channel list also available for Two DP Duals with DP34 switch
Channel list also available for Legacy Type 119/118 LNB and 110 Legacy LNB