1.Connect your receiver to tv.

2.Load 514 file below first for Sonicview 8000 HD posted on Aug. 05. 2010 according to your model via USB,let receiver reboot then turn OFF receiver.

Sonicview 8000 HD
Link>>> Sonicview 8000HD iHub FTA Fix Aug.05.2010

3.Connect Dongle/Ihub, internet and satellite dish cable to receiver.Good idea to reset router first.

4.Power up receiver.

5.Setup user settings.More settings will need to be set after loading latest file for receiver.
-----Setup dish settings and scan satellites and save settings.
-----In user options set all SID options to ON.Not all Sonicviews have the same options to set.
-----Set your local time.

6.Download and run Wiznet Tool and extract 2.2 from zip folder to your computer.Click link below for the Wiznet tool and 2.2 Ihub file.(Do not download the wiznnet tool to your memory stick, its downloaded and run via computer to your Ihub).
Link>>> iHub 2.2 firmware Wiznet 3.0.2

7.Run Wiznet Tool.
-----Click search tab.
-----Look at version in top left corner.It should show 1.4,1.9 or 2.2.You should also see IP's listed in the Wiznet Tool fields.
If it shows 1.4,1.9 or 2.1 click the upload tab on Wiznet Tool.
-----Find the extracted 2.2 file and click open.Wait until downloading complete and close all windows with Wiznet Tool.
-----Re open Wiznet Tool and click search.
-----You should now see 2.2 in the version box as seen below.If not hard boot receiver and close and reopen Wiznet tool again.IP's will vary.
-----Reboot receiver and look for "network adapter connect" message.Then try a supported channel for tv.

The steps below are for troubleshooting and serial number reset and not needed if your receiver and ihub are working at this point.

Go to the next step only if your ihub is version 2.2 in the version box of the wiznet tool.

8.Download file for your receiver.Click below.If your Ihub has WM in serial number load Jan.29.2010 fix.A wm ihub will not let you set ihub serial number don't worry.Exit and reload latest file.

-----Sonicview 8000 HD.
Link>>> Sonicview 8000HD Dongle FTA Fix Dec.26.2009
Link>>> Sonicview 8000HD Dongle FTA Fix Jan.29.2010

9.Extract file to USB and safely remove USB from pc.
-----Download file into receiver and reboot when complete.

10.Go into receiver menu and go to ipconfig
-----Enter Ihub serial number located on top of Ihub.Look closely letters and numbers are small.
-----Use the PVR control buttons
---------rewind button=A
---------play button=B
---------fast forward button=C
---------stop button=D
---------frame forward button=E
---------pause button=F
-----After setting serial number highlight Apply an click OK.(Don’t exit or it won’t save you must click apply)
-----Reboot after this to make sure ipconfig had been successfully applied.
-----After reboot you should see a message saying " Network Adapter Connect " on tv screen.

11.Go to MENU / SETTINGS/USER OPTIONS set SID options to ON / USED PRIORITY set to IHub or Both you may not have this option.Don't worry.

12.Reboot after this to make sure all changed had been successfully applied.
-----Have your receiver on cnl 200 or 300 and be patient, we’ve seen reports of picture popping up within 30 min.Normally should only take a few seconds.

13.Watch tv.

Once your Ihub is working do not change any settings/ip's in ipconfig menu or Wiznet Tool fields EVER unless instructed to do so.

As a precaution please refrain from pulling IHub off or plugging it in while SV powered up.

Attached Images

WIZ5.JPG (75.7 KB, 181 views)

__________________