banner  

Go Back   FTA Files Forums for all FTA Satellite Receivers > FTA Files & FTA Instruction & FTA Discussion Section > Viewsat FTA Receivers Support > Viewsat Files & Instructions > Viewsat Ultra FTA Files > Viewsat Ultra Instructions


Viewsat Ultra Instructions Viewsat Ultra Instructions. Get the latest Viewsat Ultra setup Instructions.

Reply
 
Thread Tools
  #1 (permalink)  
Old 02-12-2013, 11:31 AM
figueiraslick's Avatar
POWER VIP
 
Posts: 608
Thanks: 373
Thanked 735 Times in 261 Posts
Rep Power: 53
figueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond repute
Default another member having problem connecting

Do I have to get a splitter for the ethernet input on my laptop to be able to connect the xtfa router and my main router. The steps said to disable wireless on my computer but I will need an internet connection right?

This is what I have done so far.

Installed fix, factory, and cleaner files and set up the receiver.

Plugged in the router and went to the gargoyle page and entered "password" for the password.

Downloaded the firmware and did an upgrade.

Now I could not find where the factory reset is under system.

I checked my ip address and it is 192.168.1.1 and the subnet mask is 255.255.255.0

I tried to add the DNS but it said the ip was invalid.

Viewsat Ultra and the router is wireless G Router IEEE 802.iiG
Reply With Quote
  #2 (permalink)  
Old 02-12-2013, 11:34 AM
Ekim's Avatar
Jr Super Moderator
 
Location: Afghanistan
Posts: 15,177
Thanks: 1,016
Thanked 2,678 Times in 1,751 Posts
Rep Power: 861
Ekim has a reputation beyond reputeEkim has a reputation beyond reputeEkim has a reputation beyond reputeEkim has a reputation beyond reputeEkim has a reputation beyond reputeEkim has a reputation beyond reputeEkim has a reputation beyond reputeEkim has a reputation beyond reputeEkim has a reputation beyond reputeEkim has a reputation beyond reputeEkim has a reputation beyond repute
Default

You would want your xfta router connected to your main router after being setup.
__________________








I WILL NO LONGER ANSWER RECEIVER RELATED QUESTIONS BY PERSONAL MESSAGES


Reply With Quote
The Following User Says Thank You to Ekim For This Useful Post:
  #3 (permalink)  
Old 02-12-2013, 12:59 PM
figueiraslick's Avatar
POWER VIP
 
Posts: 608
Thanks: 373
Thanked 735 Times in 261 Posts
Rep Power: 53
figueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond reputefigueiraslick has a reputation beyond repute
Default

he is getting stuck at this point here is his message to me

I am trying to input the satellite settings and I do all the steps as it says.

I checked: Enable rq-ssp-client box
checked: to file
changed sssp protocol to viewsat
removed the default newcamd server
imputed the information you gave me
changed the time out to 2
pressed save all
pressed rebuild config file
pressed save all
did hard reboot
pressed start

and then when i checked the logviewer this is what i got.

Calibrating Delay: Done [10]
Initializing Serial Communication: Done

Connecting to card server (URL's truncated to 48 characters for display):
Trying: newcamd://xxxxxxxxxxxxxxxxxxxxxxxxxxx@1. nf pstv.com ... Failed
Trying: newcamd://xxxxxxxxxxxxxxxxxxxxxxxxxxxx@1 .nf pstv.com ... Failed
Trying: newcamd://xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx @1.nf pstv.com ... Failed

Failed to connect to card server(s).

Client READY! -- Waiting for requests...


--- END /tmp/rq-sssp-client.log (last modified: Feb 12 12:43:43) ---

Last edited by figueiraslick; 02-14-2013 at 09:43 AM.
Reply With Quote
  #4 (permalink)  
Old 02-13-2013, 07:57 AM
oldgoat_3's Avatar
POWER VIP
 
Posts: 80
Thanks: 186
Thanked 51 Times in 38 Posts
Rep Power: 28
oldgoat_3 has a brilliant futureoldgoat_3 has a brilliant futureoldgoat_3 has a brilliant futureoldgoat_3 has a brilliant futureoldgoat_3 has a brilliant futureoldgoat_3 has a brilliant futureoldgoat_3 has a brilliant futureoldgoat_3 has a brilliant futureoldgoat_3 has a brilliant futureoldgoat_3 has a brilliant futureoldgoat_3 has a brilliant future
Default

in your xfta router gargoyle page under systems go to reboot... click on reboot will take about a minute... save. go to satellite wait about a minute... running should come on... click on log viewer... it should connect. if not, unplug your xfta wait a few seconds then reconnect power cord... will take about a minute and a half for it to reboot. this works for me most times.

oldgoat_3
Reply With Quote
Reply

Bookmarks

Thread Tools



All times are GMT -7. The time now is 10:37 PM.